Open to PCB design roles & freelance projects

AbdulHannan

PCB Designer

I design manufacturing-ready circuit boards for embedded, IoT and mains-powered products, from the first schematic to the final Gerber files. Currently featuring GIM, a two-board heat-pump interface.

0PCB designs, from IoT nodes to mains boards
0components placed on the two GIM boards
0DRC violations cleared on a 4-layer board
Portrait of Abdul Hannan
3D render of the GIM-O PCB GIM-O · 210 × 125 mm2-layer
KiCad · EasyEDA
RP2040 · ESP32
ERC · DRC · DFM
Flagship project

GIM: one heat-pump interface, two boards.

A client project built in KiCad for JLCPCB fabrication and assembly. An outdoor board for the DIN-rail electrical box and an indoor board that switches real mains loads. Each is two-layer, 1.6 mm FR4, with mains and low-voltage circuits kept apart.

2 boards2-layer · FR4230 V sensing & switchingRP2040
More work

Seven more boards.

Instrumentation, power, industrial IoT and mixed-signal. Open any card for the full case study.

On the bench

Numbers behind the copper.

Two small tools from the way I check a layout. Move the sliders; everything is computed live in your browser.

Trace-width calculator

IPC-2221 external-layer estimate: the narrowest track that carries a current within a chosen temperature rise.

1.9mm

Drawn to true scale

Two numbers from the GIM brief, shown at their real size on your screen.

8 mmMinimum creepage and clearance between mains and low-voltage circuits, where the brief specifies it.

6 mmMinimum track width for the 13 A continuous path on GIM-I, on 2 oz copper with solder reinforcement.

2.5 mmMinimum relay contact track width for the specified 16 A relays.

Sizes use CSS millimetres, so they match real length on most screens.

Expertise

Hardware that holds up.

Schematic to manufacturing, with the electrical and fabrication checks that stop problems before the board is ordered.

PCB design

Schematic capture2 & 4-layer layoutERC / DRCTest points3D checks

Embedded & IoT

RP2040ESP32PlatformIO / ArduinoUART · SPIRS-485Nextion HMI

Power & mains

AC-DC modulesBuck & LDORelay stages230 V sensingCreepage / clearanceMOV · fuse

Review & DFM

StackupSolder-mask rulesIPC-2221BOM sourcingGerber · CPLJLCPCB
Process

From requirement to Gerber.

01

Requirements

Read the spec, constraints and reference data before touching a schematic.

02

Validate

Simulate or calculate the critical circuits so the architecture is proven early.

03

Schematic & layout

Clean schematics, deliberate placement, power and isolation planned first.

04

Verify & DFM

ERC, DRC, stackup, mask and footprint checks against the fab's real limits.

05

Hand-off

Gerbers, BOM, placement file and notes documenting every decision.

Abdul Hannan
Abdul HannanElectronics Engineer · 2026
About

Engineer first, always.

I'm Abdul Hannan, an Electronics Engineering graduate from The Islamia University of Bahawalpur (2026). My work sits where hardware meets firmware: RP2040 and ESP32 controllers, mains-side power stages, analog front ends and instruments that have to be right the first time.

I care about the unglamorous details: correct stackups, creepage you can measure, sensible test points, parts that are in stock, and notes another engineer can pick up. Next to board design I work with embedded systems, Edge AI and TinyML.

Every project here was built against a real client specification, and I describe each one by what was actually designed and verified.

LocationBahawalpur, Pakistan
Local time--:--
EducationElectronics Engineering, IUB
FocusPCB · Embedded · IoT
ExploringEdge AI · TinyML
AvailabilityOpen to opportunities

Let's build something reliable.

Have a board to design, review or finalize for manufacturing? Send me the requirements and I'll reply with a clear plan.

Chat on WhatsApp0309 0093336 Call+92 309 0093336 LinkedInAbdul Hannan
© 2026 Abdul Hannan · Bahawalpur, PakistanBack to top ↑
Email copied